Log In | Sign Up
CategoriesAll
Plastic Raw Materials
Modified Plastics
Plastic Additives
Color Masterbatch
Plastic Datasheets
Plastic News
About Us

Material Comparison

Product Info
Product Name
Brand Name
Usages
Properties
Certificates
PC LUX2614 SABIC INNOVATIVE NANSHA
LEXAN™ 
Flame retardant,UV resistance
Flame retardant,UV resistance
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--

Plastic Datasheets

Impact resistanceTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
Suspended wall beam without notch impact strength23°CASTM D48123200 J/m
Impact strength of cantilever beam gapASTM D1822546 kJ/m²
Dart impact23°CASTM D3029169 J
hardnessTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
Rockwell hardnessM 级ASTM D78570
R 级ASTM D785118
Mechanical propertiesTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
Tensile modulusISO 527-2/12300 Mpa
tensile strength 屈服2ASTM D63862.0 Mpa
elongation断裂2ASTM D638110 %
Taber abraser1000 Cycles, 1000 g, CS-17 转轮ASTM D104410.0 mg
Flexural modulus--4ISO 1782300 Mpa
bending strength屈服, 50.0 mm 跨距3ASTM D79093.0 Mpa
--4,5ISO 17894.0 Mpa
Flexural modulus50.0 mm 跨距3ASTM D7902340 Mpa
tensile strength 断裂ISO 527-2/5063.0 Mpa
屈服ISO 527-2/5063.0 Mpa
elongation屈服2ASTM D6387.0 %
屈服ISO 527-2/506.0 %
tensile strength 断裂2ASTM D63865.0 Mpa
Electrical performanceTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
Volume resistivityASTM D257> 1.0E+17 ohms·cm
dielectric constant60 HzASTM D1503.17
Dissipation Factor60 HzASTM D1509.0E-4
50 HzASTM D1509.0E-4
dielectric constant1 MHzASTM D1502.96
Hot wire ignition (HWI)UL 746PLC 3
dielectric strength3.20 mm, in AirASTM D14915 KV/mm
Compared to the Leakage Tracking Index (CTI)UL 746PLC 3
Dissipation Factor1 MHzASTM D1500.010
High arc combustion index (HAI)UL 746PLC 1
dielectric constant50 kHzASTM D1503.17
optical performance Test ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
refractive indexASTM D5421.586
flammabilityTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
Hot filament ignition temperature1.5 mmIEC 60695-2-13850 °C
0.75 mm9IEC 60695-2-13875 °C
Burning wire flammability index0.75 mmIEC 60695-2-12750 °C
1.5 mmIEC 60695-2-12850 °C
UL flame retardant rating0.817mmUL 94V-2
physical property Test ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
Water absorption rate平衡, 23°CASTM D5700.35 %
平衡, 100°CASTM D5700.58 %
Melt volume flow rate300°C/1.2 kgISO 11337.00 cm3/10min
Outdoor applicabilityUL 746Cf2
Water absorption rate24 hrASTM D5700.15 %
Specific volumeASTM D7920.830 cm³/g
melt mass-flow rate300°C/1.2 kgASTM D12387.0 g/10 min
Shrinkage rate3.20 mm，Flow内部方法0.50 - 0.70 %
Thermal performanceTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
vicat--ISO 306/B120145 °C
thermal conductivityASTM C1770.29 W/m/K
vicat--ASTM D15257154 °C
Linear coefficient of thermal expansion-40 到 95°C，流动ASTM E8316.8E-5 cm/cm/°C
specific heatASTM C3511260 J/kg/°C
Heat distortion temperature1.8 MPa, 未退火, 6.40 mm，HDTASTM D648132 °C
RTI ImpUL 74680.0 °C
ball-indentation hardness123 到 127°CIEC 60695-10-2通过
RTIUL 74680.0 °C
Heat distortion temperature0.45 MPa, 未退火, 6.40 mm，HDTASTM D648137 °C
RTI ElecUL 74680.0 °C
injectionTest ConditionTest MethodSABIC INNOVATIVE NANSHA/LUX2614
screw speed40 to 70 rpm
Suggested maximum moisture content0.020 %
Processing (melt) temperature310 to 330 °C
drying temperature120 °C
Suggested injection volume40 to 60 %
drying time3.0 to 4.0 hr
Temperature in the middle of the barrel300 to 320 °C
Temperature at the rear of the barrel290 to 310 °C
Exhaust hole depth0.025 to 0.076 mm
Temperature at the front of the material cylinder310 to 330 °C
Back pressure0.300 to 0.700 Mpa
Temperature80 to 115 °C
Spray nozzle temperature305 to 325 °C

Contact Us

Get App

Top