Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | MD:3.20mm | 内部方法 | 0.20to0.40 | % |
Moisture Absorption | 24hr | ASTMD570 | 0.12 | % |
Moisture Absorption | Equilibrium,23°C | ASTMD570 | 0.31 | % |
Outdoor Suitability | | UL746C | f1 | |
Specific Volume | | ASTMD792 | 0.802 | cm³/g |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Strength | Yield | ASTMD638 | 66.2 | Mpa |
Tensile Strength | Break | ASTMD638 | 55.2 | Mpa |
Tensile Elongation | Yield | ASTMD638 | 8.0 | % |
Tensile Elongation | Break | ASTMD638 | 15 | % |
Flexural Modulus | 50.0mmSpan | ASTMD790 | 3450 | Mpa |
Flexural Strength | Yield,50.0mmSpan | ASTMD790 | 103 | Mpa |
Taber Abrasion Resistance | 1000Cycles,1000g,CS-17Wheel | ASTMD1044 | 11.0 | mg |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Heat Deflection Temperature | 0.45MPa,Unannealed,6.40mm | ASTMD648 | 146 | °C |
Heat Deflection Temperature | 1.8MPa,Unannealed,6.40mm | ASTMD648 | 142 | °C |
Vicat Softening Temperature | | ASTMD15255 | 154 | °C |
Coefficient of Linear Thermal Expansion | MD:-40to95°C | ASTME831 | 3.2E-05 | cm/cm/°C |
Specific Heat | | ASTMC351 | 1210 | J/kg/°C |
Thermal Conductivity | | ASTMC177 | 0.20 | W/m/K |
RTIElec | | UL746 | 120 | °C |
RTIImp | | UL746 | 110 | °C |
RTIStr | | UL746 | 125 | °C |
Electrical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Volume Resistivity | | ASTMD257 | >1.0E+17 | ohms·cm |
Dielectric Strength | 3.20mm,inAir | ASTMD149 | 18 | KV/mm |
Dielectric Constant | 50Hz | ASTMD150 | 3.10 | |
Dielectric Constant | 60Hz | ASTMD150 | 3.10 | |
Dielectric Constant | 1MHz | ASTMD150 | 3.05 | |
Dissipation Factor | 50Hz | ASTMD150 | 8E-04 | |
Dissipation Factor | 60Hz | ASTMD150 | 8E-04 | |
Dissipation Factor | 1MHz | ASTMD150 | 7.5E-03 | |
Arc Resistance | | ASTMD495 | PLC7 | |
Comparative Tracking Index | CTI | UL746 | PLC4 | |
High Amp Arc Ignition | HAI | UL746 | PLC1 | |
High Voltage Arc Tracking Rate | HVTR | UL746 | PLC3 | |
Hot-wire Ignition | HWI | UL746 | PLC1 | |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Gardner Impact | 23°C | ASTMD3029 | 102 | J |
Tensile Impact Strength | | ASTMD1822 | 158 | kJ/m² |
Hardness | Test Condition | Test Method | Test Result | Unit |
---|
Rockwell Hardness | M-Sale | ASTMD785 | 85 | |
Rockwell Hardness | R-Sale | ASTMD785 | 124 | |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Flame Rating | 1.5mm | UL94 | V-0 | |
Flame Rating | 3.0mm | UL94 | 5VA | |
Oxygen Index | | ASTMD2863 | 36 | % |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.