Technical Data Sheet
| Physical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Modeling Shrinkage | Across Flow | ISO 294-4 | 1.4 | % |
| Modeling Shrinkage | 流量 | ISO 294-4 | 1.4 | % |
| Moisture Absorption | Saturation, 23°C, 2.00 mm | ISO 62 | 8.5 | % |
| Moisture Absorption | Equilibrium, 23°C, 2.00 mm, 50% RH | ISO 62 | 2.6 | % |
| Viscosity number | 96% H2SO4 | ISO 307 | 150 | cm³/g |
| Density | | ISO 1183 | 1.14 | g/cm³ |
| Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Nominal Tensile Strain at Break | | ISO 527-2 | 25 | % |
| Tensile Stress | Yield | ISO 527-2 | 82.0 | Mpa |
| Tensile Strain | Yield | ISO 527-2 | 4.5 | % |
| Tensile Creep Modulus | 1 hr | ISO 899-1 | -- | Mpa |
| Tensile Creep Modulus | 1000 hr | ISO 899-1 | -- | Mpa |
| Tensile Modulus | | ISO 527-2 | 3100 | Mpa |
| Flexural Modulus | | ISO 178 | 2800 | Mpa |
| Thermal Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Deflection Temperature Under Load? | 0.45 MPa, Unannealed | ISO 75-2/B | 190 | °C |
| Deflection Temperature Under Load? | 1.8 MPa, Unannealed | ISO 75-2/A | 70.0 | °C |
| Linear thermal expansion coefficient | Flow | ISO 11359-2 | 1.0E-4 | cm/cm/°C |
| Linear thermal expansion coefficient | Across Flow | ISO 11359-2 | 1.1E-4 | cm/cm/°C |
| Vicat Softening Temperature | | ISO 306/B50 | 240 | °C |
| Glass Transition Temperature | | ISO 11357-2 | 60.0 | °C |
| Melting Temperature | | ISO 11357-3 | 262 | °C |
| Effective Thermal Diffusivity | | | 5.00E-8 | m²/s |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Dissipation Factor? | 100 Hz | IEC 62631-2-1 | 8.0E-3 | |
| Dissipation Factor? | 1 MHz | IEC 62631-2-1 | 0.018 | |
| Dielectric Strength | | IEC 60243-1 | 32 | KV/mm |
| Relative Permittivity | 1 MHz | IEC 62631-2-1 | 3.50 | |
| Relative Permittivity | 100 Hz | IEC 62631-2-1 | 3.80 | |
| Comparative Tracking Index | | IEC 60112 | 600 | V |
| Surface Resistivity | | IEC 62631-3-2 | -- | ohms |
| Volume Resistivity | | IEC 62631-3-1 | 1.0E+12 | ohms·m |
| Film | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile Elongation (MD) | Yield | ISO 527-3 | 4.5 | % |
| Fill Analysis | Test Condition | Test Method | Test Result | Unit |
|---|
| Emission of Organic Compounds | | VDA 277 | 5.00 | µgC/g |
| Melt Density | | | 0.970 | g/cm³ |
| Ejection Temperature | | | 190 | °C |
| Specific Heat Capacity of Melt | | | 2790 | J/kg/°C |
| Thermal Conductivity of Melt | | | 0.16 | W/m/K |
| Odor | | VDA 270 | 3.00 | |
| Injection | Test Condition | Test Method | Test Result | Unit |
|---|
| Drying Temperature | | | 80 | °C |
| Drying time - Hot air dryer | | | 2.0 到 4.0 | hr |
| Suggested Max Moisture | | | 0.20 | % |
| Processing (Melt) Temp | | | 280 到 300 | °C |
| Melt Temperature, Optimum | | | 290 | °C |
| Mold Temperature | | | 50 到 90 | °C |
| Mold Temperature, Optimum | | | 70 | °C |
| Holding Pressure | | | 50.0 到 100 | Mpa |
| Holding Pressure | Drying Recommended | | yes | |
| Hold Pressure Time | | | 4.00 | s/mm |
| Maximum Screw Tangential Speed | | | 24 | m/min |
| Impact Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Charpy Unnotched Impact Strength | -30°C | ISO 179/1eU | 400 kJ/m² | |
| Charpy Unnotched Impact Strength | 23°C | ISO 179/1eU | 无断裂 | |
| Charpy Notched Impact Strength | -30°C | ISO 179/1eA | 4.5 | kJ/m² |
| Charpy Notched Impact Strength | 23°C | ISO 179/1eA | 5.5 | kJ/m² |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell Hardness | M -Sale | ISO 2039-2 | 79 | |
| Rockwell Hardness | R -Sale | ISO 2039-2 | 121 | |
| Flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| atomization | F-value (refraction) | ISO 6452 | 99 | % |
| atomization | G-value (condensate) | ISO 6452 | 1.0E-4 | g |
| Flame Rating | 0.70 mm | UL 94, IEC 60695-11-10, -20 | V-2 | |
| Flame Rating | 1.5 mm | UL 94, IEC 60695-11-10, -20 | V-2 | |
| FMVSS Flammability | | FMVSS 302 | DNI | |
| Oxygen Index | | ISO 4589-2 | 28 | % |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
