Material Properties
| Physical | Test Condition | Test Method | Test Result | Unit |
|---|
| Modeling Shrinkage | MD1 | 内部方法 | 0.50到0.70 | % |
| Moisture Absorption | Saturation,23°C | ISO62 | 0.35 | % |
| Moisture Absorption | Equilibrium,23°C,50%RH | ISO62 | 0.15 | % |
| Outdoor Suitability | | UL746C | f1 | |
| Melt Volume flow Rate | 300°C/1.2kg | ISO1133 | 10.0 | cm3/10min |
| Mechanical | Test Condition | Test Method | Test Result | Unit |
|---|
| Flexural Stress | | ISO178 | 90.0 | Mpa |
| Tensile Stress | Yield | ISO527-2/50 | 63.0 | Mpa |
| Tensile Stress | Break | ISO527-2/50 | 65.0 | Mpa |
| Tensile Strain | Yield | ISO527-2/50 | 6.0 | % |
| Tensile Strain | Break | ISO527-2/50 | 100 | % |
| Tensile Modulus | | ISO527-2/1 | 2350 | Mpa |
| Flexural Modulus | | ISO178 | 2300 | Mpa |
| Optical | Test Condition | Test Method | Test Result | Unit |
|---|
| Light Transmittance | 2540µm | ASTMD1003 | 88.0 | % |
| Index of Refraction | | ISO489 | 1.586 | |
| Thermal | Test Condition | Test Method | Test Result | Unit |
|---|
| Thermal Conductivity | | ISO8302 | 0.20 | W/m/K |
| 0.45MPa, Unannealed,100mm Span | | ISO75-2/Be | 136 | °C |
| 1.8MPa, Unannealed,100mm Span | | ISO75-2/Ae | 125 | °C |
| RTI | | UL746 | 125 | °C |
| Ball PressureTest | 125°C | IEC60695-10-2 | Pass | |
| -- | | ISO306/B50 | 141 | °C |
| -- | | ISO306/B120 | 142 | °C |
| Coefficient of Linear Thermal Expansion | MD:23to80°C | ISO11359-2 | 7E-05 | cm/cm/°C |
| Coefficient of Linear Thermal Expansion | TD:23to80°C | ISO11359-2 | 7E-05 | cm/cm/°C |
| RTIElec | | UL746 | 130 | °C |
| RTIImp | | UL746 | 120 | °C |
| Electrical | Test Condition | Test Method | Test Result | Unit |
|---|
| Dissipation Factor | 50Hz | IEC60250 | 1E-03 | |
| Dissipation Factor | 60Hz | IEC60250 | 1E-03 | |
| Dissipation Factor | 1MHz | IEC60250 | 0.010 | |
| Surface Resistivity | | IEC60093 | >1.0E+15 | ohms |
| Volume Resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
| Dielectric Strength | 3.20mm,in Oil | IEC60243-1 | 17 | KV/mm |
| Relative Permittivity | 50Hz | IEC60250 | 2.70 | |
| Relative Permittivity | 60Hz | IEC60250 | 2.70 | |
| Relative Permittivity | 1MHz | IEC60250 | 2.70 | |
| Comparative Tracking Index | | IEC60112 | 225 | V |
| Impact | Test Condition | Test Method | Test Result | Unit |
|---|
| Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | 无断裂 | |
| Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | 无断裂 | |
| Notched Izod Impact Strength | -30°C | ISO180/1A | 12 | kJ/m² |
| Notched Izod Impact Strength | 23°C | ISO180/1A | 70 | kJ/m² |
| Unnotched Izod Impact Strength | -30°C | ISO180/1U | 无断裂 | |
| Unnotched Izod Impact Strength | 23°C | ISO180/1U | 无断裂 | |
| Charpy Notched Impact Strength | -30°C | ISO179/1eA | 14 | kJ/m² |
| Charpy Notched Impact Strength | 23°C | ISO179/1eA | 73 | kJ/m² |
| Hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Ball Indentation Hardness | H358/30 | ISO2039-1 | 95.0 | Mpa |
| Flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| Flame Rating | 1.50mm | UL94 | V-2 | |
| Flame Rating | 3.00mm | UL94 | V-0 | |
| Glow Wire Flammability Index | 1.00mm | IEC60695-2-12 | 960 | °C |
| Oxygen Index | | ISO4589-2 | 35 | % |
| Glow Wire Ignition Temperature | 1.00mm | IEC60695-2-13 | 850 | °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
