Technical Data Sheet Compare

hardness	Test Condition	Test Method	Test Result
ball-indentation hardness		ISO 2039-1	130 Mpa

thermal performance	Test Condition	Test Method	Test Result
Heat Deflection Temperature	0.45 MPa, 未退火	ISO 75-2/B	191 °C
Heat Deflection Temperature	Heat Deflection Temperature	1.8 MPa, 未退火	ISO 75-2/A	172 °C
vicat		ISO 306/B120	202 °C
Linear coefficient of thermal expansion	流动 : 23 到 55°C	ISO 11359-2	6.5E-5 cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	横向 : 23 到 55°C	ISO 11359-2	6.5E-5 cm/cm/°C
RTI Elec		UL 746	150 °C
RTI Imp		UL 746	130 °C
RTI		UL 746	150 °C

optical performance	Test Condition	Test Method	Test Result
refractive index		ISO 489	1.566
transmissivity	1000 µm	ISO 13468-2	89.0 %
electrolytic corrosion	23°C	IEC 60426	A1

flammability	Test Condition	Test Method	Test Result
UL flame retardant rating	1.5 mm	UL 94	HB
Burning wire flammability index		IEC 60695-2-12	800 °C
Limiting Oxygen Index		ISO 4589-2	25 %

Impact resistance	Test Condition	Test Method	Test Result
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂

Physical properties	Test Condition	Test Method	Test Result
density	23°C	ISO 1183	1.13 g/cm³
melt mass-flow rate	330°C/2.16 kg	ISO 1133	8.0 g/10 min
Melt volume flow rate	330°C/2.16 kg	ISO 1133	8.00 cm3/10min
shrinkage rate	横向流量 : 2.00 mm	ISO 294-4	0.90 %
shrinkage rate	shrinkage rate	流量 : 2.00 mm	ISO 294-4	0.90 %
Water absorption rate	饱和, 23°C	ISO 62	0.30 %
Water absorption rate	Water absorption rate	平衡, 23°C, 50% RH	ISO 62	0.12 %

Electrical performance	Test Condition	Test Method	Test Result
Surface Resistivity		IEC 60093	1.0E+16 ohms
volume resistivity	23°C	IEC 60093	1.0E+17 ohms·cm
dielectric strength	23°C, 1.00 mm	IEC 60243-1	35 KV/mm
relative permittivity	23°C, 100 Hz	IEC 60250	2.90
relative permittivity	relative permittivity	23°C, 1 MHz	IEC 60250	2.80
Dissipation Factor	23°C, 100 Hz	IEC 60250	1.0E-3
Dissipation Factor	Dissipation Factor	23°C, 1 MHz	IEC 60250	9.0E-3
Compared to the Leakage Tracking Index (CTI)	解决方案 A	IEC 60112	PLC 0
Compared to the Leakage Tracking Index (CTI)	Compared to the Leakage Tracking Index (CTI)	解决方案 B	IEC 60112	PLC 4

injection	Test Condition	Test Method	Test Result
Drying Temperature - Dry Air Dryer			130 °C
Drying time - Dry Air Dryer			2.0 to 4.0 hr
Suggested maximum moisture content			< 0.020 %
Suggested injection volume			30 to 70 %
Temperature at the rear of the barrel			315 to 325 °C
Temperature in the middle of the barrel			320 to 330 °C
Temperature at the front of the material cylinder			325 to 335 °C
Spray nozzle temperature			315 to 340 °C
Processing (melt) temperature			330 to 340 °C
mold temperature			110 to 150 °C
Back pressure			10.0 to 20.0 Mpa
Exhaust hole depth			0.025 to 0.050 mm

mechanical properties	Test Condition	Test Method	Test Result
Tensile modulus	23°C	ISO 527-2/1	2450 Mpa
tensile strength	屈服, 23°C	ISO 527-2/50	76.0 Mpa
Tensile strain	屈服, 23°C	ISO 527-2/50	6.9 %
Nominal tensile fracture strain	23°C	ISO 527-2/50	> 50 %
flexural modulus	23°C	ISO 178	2450 Mpa
bending strength	23°C	ISO 178	110 Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top