optical performance	Test Condition	Test Method	Test Result	Test Unit
Refractive index		ISO 179/leA	1.586
transmissivity	2540 μm	ASTM D1003	88.0 to 90.0	%
turbidity	2540 μm	ASTM D1003	< 0.80	%
impact performance	Test Condition	Test Method	Test Result	Test Unit
Suspended wall beam without notch impact strength	23°C	ASTM D4812	无断裂
Suspended wall beam without notch impact strength	Suspended wall beam without notch impact strength	-30°C8	ISO 180/1U	无断裂
Dart impact	23°C, Energy at Peak	ASTM D3763	55.0	J
flammability	Test Condition	Test Method	Test Result	Test Unit
UL flame retardant rating	1.5 mm	UL 94	V-2
mechanical properties	Test Condition	Test Method	Test Result	Test Unit
Tensile modulus	--3	ASTM D638	2350	Mpa
Tensile modulus	Tensile modulus	--	ISO 527-2/1	2350	Mpa
tensile strength	Yield4	ASTM D638	63.0	Mpa
tensile strength	tensile strength	Yield	ISO 527-2/50	63.0	Mpa
elongation	Yield4	ASTM D638	6.0	%
	elongation	Yield	ISO 527-2/50	6.0	%
		elongation	Break4	ASTM D638	> 70	%
		elongation	elongation	Break	ISO 527-2/50	> 70	%
Bending modulus	50.0 mm Span5	ASTM D790	2300	Mpa
Bending modulus	Bending modulus	--6	ISO 178	2300	Mpa
bending strength	--6,7	ISO 178	90.0	Mpa
bending strength	bending strength	Yield, 50.0 mm Span5	ASTM D790	90.0	Mpa
injection	Test Condition	Test Method	Test Result	Test Unit
drying temperature			120	°C
drying time			2.0 to 4.0	hr
Suggested maximum moisture content			0.020	%
Hopper temperature			60 to 80	°C
Temperature at the rear of the barrel			260 to 280	°C
Temperature in the middle of the barrel			270 to 290	°C
Temperature at the front of the material cylinder			280 to 300	°C
Spray nozzle temperature			270 to 290	°C
Processing (melt) temperature			280 to 300	°C
Mold temperature			80 to 100	°C
thermal performance	Test Condition	Test Method	Test Result	Test Unit
Hot deformation temperature	0.45 MPa, Unannealed, 3.20 mm	ASTM D648	133	°C
	Hot deformation temperature	0.45 MPa, Unannealed, 4.00 mm, 64.0 mm Span9	ISO 75-2/Bf	133	°C
		Hot deformation temperature	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	122	°C
		Hot deformation temperature	Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span9	ISO 75-2/Af	122	°C
Vicat softening temperature		ISO 306/B50	140	°C
Ball Pressure Test	123 to 127°C	IEC 60695-10-2	通过
Linear coefficient of thermal expansion	-40 to 95°C，Flow	ASTM E831	7.0E-5	cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	23 to 80°C，Flow	ISO 11359-2	7.0E-5	cm/cm/°C
thermal conductivity		ASTM C177	0.20	W/m/K
Physical properties	Test Condition	Test Method	Test Result	Test Unit
melt mass-flow rate	300°C/1.2 kg	ASTM D1238	22	g/10 min
Melt Volume Flow Rate (MVR)	300°C/1.2 kg	ISO 1133	21.0	cm3/10min
Shrinkage rate	--2，Flow	Internal Method	0.50 - 0.70	%
Shrinkage rate	Shrinkage rate	3.20 mm，Flow	Internal Method	0.50 - 0.70	%
Water absorption rate	Saturation, 23°C	ISO 62	0.35	%
Water absorption rate	Water absorption rate	Equilibrium, 23°C	ASTM D570	0.35	%
Electrical performance	Test Condition	Test Method	Test Result	Test Unit
Volume resistivity		ASTM D257	> 1.0E+15	ohms·cm
Dielectric strength	1.60 mm	ASTM D149	27	KV/mm
Dielectric constant	60 Hz	ASTM D150	3.00
Dielectric constant	Dielectric constant	1 MHz	ASTM D150	3.00
Dissipation factor	60 Hz	ASTM D150	1.0E-3
Dissipation factor	Dissipation factor	1 MHz	ASTM D150	0.010
hardness	Test Condition	Test Method	Test Result	Test Unit
Rockwell hardness	R-Scale	ASTM D785	120
Rockwell hardness	Rockwell hardness	R -Sale	ISO 2039-2	120

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top