thermal performance	Test Condition	Test Method	Test Result
Heat Deflection Temperature	0.45 MPa, 未退火	ISO 75-2/B	157 °C
Heat Deflection Temperature	Heat Deflection Temperature	1.8 MPa, 未退火	ISO 75-2/A	63.0 °C
Glass Transition Temperature		ISO 11357-2	75.0 °C
vicat		ISO 306/B50	205 °C
melting temperature		ISO 11357-3	262 °C
Linear coefficient of thermal expansion	流动 : 23 到 55°C	ASTM E831	1.4E-4 cm/cm/°C
	Linear coefficient of thermal expansion	流动	ISO 11359-2	1.4E-4 cm/cm/°C
		Linear coefficient of thermal expansion	流动 : -40 到 23°C	ISO 11359-2	1.1E-4 cm/cm/°C
			Linear coefficient of thermal expansion	流动 : 55 到 160°C	ISO 11359-2	1.6E-4 cm/cm/°C
				Linear coefficient of thermal expansion	横向 : 23 到 55°C	ASTM E831	1.3E-4 cm/cm/°C
					Linear coefficient of thermal expansion	横向	ISO 11359-2	1.3E-4 cm/cm/°C
						Linear coefficient of thermal expansion	横向 : -40 到 23°C	ISO 11359-2	1.1E-4 cm/cm/°C
						Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	横向 : 55 到 160°C	ISO 11359-2	1.3E-4 cm/cm/°C

flammability	Test Condition	Test Method	Test Result
burning rate	1.00 mm	ISO 3795	< 100 mm/min
UL flame retardant rating		UL 94	HB
UL flame retardant rating	UL flame retardant rating		UL 94	HB
Limiting Oxygen Index		ISO 4589-2	20 %
FMVSS combustion rate		FMVSS 302	B

Impact resistance	Test Condition	Test Method	Test Result
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	20 kJ/m²
Charpy Notched Impact Strength	Charpy Notched Impact Strength	23°C, 局部断裂	ISO 179/1eA	70 kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	--
Impact strength of cantilever beam gap	-40°C	ISO 180/1A	20 kJ/m²
	Impact strength of cantilever beam gap	-30°C	ISO 180/1A	15 kJ/m²
	Impact strength of cantilever beam gap	Impact strength of cantilever beam gap	23°C	ISO 180/1A	80 kJ/m²

Filling analysis	Test Condition	Test Method	Test Result
Ejection Temperature			190 °C

Physical properties	Test Condition	Test Method	Test Result
density		ISO 1183	1.07 g/cm³
shrinkage rate	横向流量	ISO 294-4	1.4 %
shrinkage rate	shrinkage rate	流量	ISO 294-4	1.8 %
Water absorption rate	24 hr, 23°C	ISO 62	1.1 %
	Water absorption rate	饱和, 23°C, 2.00 mm	ISO 62	6.5 %
	Water absorption rate	Water absorption rate	平衡, 23°C, 2.00 mm, 50% RH	ISO 62	2.0 %
viscosity number		ISO 307	130 cm³/g

Electrical performance	Test Condition	Test Method	Test Result
Surface Resistivity		IEC 62631-3-2	-- ohms
volume resistivity		IEC 62631-3-1	> 1.0E+13 ohms·m
dielectric strength		IEC 60243-1	25 KV/mm
relative permittivity	1 MHz	IEC 62631-2-1	3.30
relative permittivity	relative permittivity	100 Hz	IEC 62631-2-1	3.50
Dissipation Factor	100 Hz	IEC 62631-2-1	5.0E-3
Dissipation Factor	Dissipation Factor	1 MHz	IEC 62631-2-1	0.010
Compared to the Leakage Tracking Index (CTI)		IEC 60112	V

injection	Test Condition	Test Method	Test Result
drying temperature			80 °C
Drying time - hot air dryer			2.0 to 4.0 hr
Suggested maximum moisture content			0.20 %
Processing (melt) temperature			280 to 300 °C
Melt Temperature, Optimum			290 °C
mold temperature			50 to 100 °C
Mold Temperature, Optimum			80 °C
pressure holding			50.0 to 100 Mpa
pressure holding	pressure holding	Drying Recommended		yes
Hold Pressure Time			4.00 s/mm
Maximum Screw Tangential Speed			18 m/min

mechanical properties	Test Condition	Test Method	Test Result
Tensile modulus		ISO 527-2	2000 Mpa
tensile strength	50% 应变	ISO 527-2	49.0 Mpa
Tensile strain	断裂	ISO 527-2	> 50 %
Tensile creep modulus	1 hr	ISO 899-1	-- Mpa
Tensile creep modulus	Tensile creep modulus	1000 hr	ISO 899-1	-- Mpa
flexural modulus		ISO 178	1800 Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top