Technical Data Sheet hardness Test Condition Test Method Test Result Ball Pressure Test ISO 2039-1 149 Mpa
thermal performance Test Condition Test Method Test Result Hot deformation temperature 0.45MPa,Unannealed ISO 75-2/B 141 °C Hot deformation temperature 1.8MPa,Unannealed ISO 75-2/A 135 °C Vicat softening temperature -- ISO 306/B50 147 °C Vicat softening temperature -- ISO 306/B120 148 °C Ball Pressure Test 137°C IEC 60695-10-2 Pass Linear coefficient of thermal expansion MD：23to55°C ISO 11359-2 3.5E-05 cm/cm/°C Linear coefficient of thermal expansion TD：23to55°C ISO 11359-2 5.5E-05 cm/cm/°C thermal conductivity 23°C ISO 8302 0.24 W/m/K RTI Elec 1.5mm UL 746 125 °C RTI Imp 1.5mm UL 746 115 °C RTI Str 1.5mm UL 746 125 °C
flammability Test Condition Test Method Test Result Needle flame test MethodF:1.50mm IEC 60695-11-5 2.0 min Needle flame test MethodF:2.00mm IEC 60695-11-5 2.0 min Needle flame test MethodF:3.00mm IEC 60695-11-5 2.0 min Needle flame test MethodK:1.50mm IEC 60695-11-5 1.0 min Needle flame test MethodK:2.00mm IEC 60695-11-5 1.0 min Needle flame test MethodK:3.00mm IEC 60695-11-5 2.0 min SelfIgnition ASTM D1929 550 °C UL flame retardant rating 1.5mm UL 94 V-1 Burning wire flammability index 0.75mm IEC 60695-2-12 960 °C Burning wire flammability index 1.5mm IEC 60695-2-12 960 °C Burning wire flammability index 3.0mm IEC 60695-2-12 960 °C Hot filament ignition temperature 0.75mm IEC 60695-2-13 875 °C Hot filament ignition temperature 1.5mm IEC 60695-2-13 875 °C Hot filament ignition temperature 3.0mm IEC 60695-2-13 875 °C Extreme Oxygen Index ISO 4589-2 37 % ApplicationofFlamefromSmallBurner MethodKandF 2.00mm DIN 53438-1,-3 K1.F1 Burning rate - US-FMVSS >1.00mm ISO 3795 passed FlashIgnitionTemperature ASTM D1929 470 °C
Supplementary Information Test Condition Test Method Test Result Electrolytic corrosion 23°C IEC 60426 A1
Physical properties Test Condition Test Method Test Result density 23°C ISO 1183 1.42 g/cm³ Apparent density ISO 60 0.69 g/cm³ melt mass-flow rate 300°C/1.2kg ISO 1133 5.0 g/10min Melt Volume Flow Rate (MVR) 300°C/1.2kg ISO 1133 4.00 cm3/10min Shrinkage rate TD ISO 2577 0.25-0.40 % Shrinkage rate MD ISO 2577 0.25-0.40 % Shrinkage rate TD:2.00mm3 ISO 294-4 0.35 % Shrinkage rate MD:2.00mm3 ISO 294-4 0.50 % Water absorption rate Saturation,23°C ISO 62 0.22 % Water absorption rate Equilibrium,23°C,50%RH ISO 62 0.10 %
Electrical performance Test Condition Test Method Test Result Surface resistivity IEC 60093 1E+16 ohms Volume resistivity 23°C IEC 60093 1E+16 ohms·cm Dielectric strength 23°C,1.00mm IEC 60243-1 36 KV/mm Relative permittivity 23°C,100Hz IEC 60250 3.50 Relative permittivity 23°C,1MHz IEC 60250 3.50 Dissipation factor 23°C,100Hz IEC 60250 1.5E-03 Dissipation factor 23°C,1MHz IEC 60250 9E-03 Compared to the anti leakage trace index SolutionA IEC 60112 PLC 3 Compared to the anti leakage trace index SolutionB IEC 60112 PLC 4
mechanical properties Test Condition Test Method Test Result tensile strength Break,23°C ISO 527-2/5 55.0 Mpa Tensile strain Yield,23°C ISO 527-2/50 2.5 % Tensile strain Break,23°C ISO 527-2/5 3.5 % Tensile creep modulus 1hr ISO 899-1 4700 Mpa Tensile creep modulus 1000hr ISO 899-1 3900 Mpa Bending modulus 23°C ISO 178 4700 Mpa bending strength 3.5%Strain,23°C ISO 178 100 Mpa bending strength 23°C ISO 178 105 Mpa Bending strain 23°C ISO 178 4.5 % Tensile modulus 23°C ISO 527-2/1 5100 Mpa tensile strength Yield,23°C ISO 527-2/50 59.0 Mpa
impact performance Test Condition Test Method Test Result Charpy Notched Impact Strength 23°C,CompleteBreak ISO 7391 8.0 kJ/m² Impact strength of simply supported beam without notch -60°C,CompleteBreak ISO 179/1eU 45 kJ/m² Impact strength of simply supported beam without notch -30°C,Complete Break ISO 179/1eU 45 kJ/m² Impact strength of simply supported beam without notch 23°C,Complete Break ISO 179/1eU 40 kJ/m² Impact strength of cantilever beam gap 23°C,CompleteBreak ISO 7391 8.0 kJ/m² Multi axis Instrumented Impact Energy -30°C ISO 6603-2 5.00 J Multi axis Instrumented Impact Energy 23°C ISO 6603-2 5.00 J Multi axis Instrumented Peak Impact Force -30°C ISO 6603-2 800 N Multi axis Instrumented Peak Impact Force 23°C ISO 6603-2 1300 N
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
