thermal performance	Test Condition	Test Method	Test Result
Heat Deflection Temperature	0.45 MPa, 未退火, 6.40 mm	ASTM D648	210 °C
Heat Deflection Temperature	Heat Deflection Temperature	1.8 MPa, 未退火, 6.40 mm	ASTM D648	182 °C
Linear coefficient of thermal expansion	-40 到 40°C，流动	ASTM E831	2.0E-5 cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	60 到 138°C，流动	ASTM E831	2.0E-5 cm/cm/°C
RTI Elec		UL 746	120 °C
RTI Imp		UL 746	120 °C
RTI		UL 746	140 °C

flammability	Test Condition	Test Method	Test Result
UL flame retardant rating	0.9 mm	UL 94	V-0
UL flame retardant rating	UL flame retardant rating	3.0 mm	UL 94	5VA
Limiting Oxygen Index		ASTM D2863	29 %

Impact resistance	Test Condition	Test Method	Test Result
Suspended wall beam without notch impact strength	23°C	ASTM D4812	500 J/m

Physical properties	Test Condition	Test Method	Test Result
Specific volume		ASTM D792	0.650 cm³/g
shrinkage rate	流动 : 1.50 到 3.20 mm	内部方法	0.40 - 0.60 %
	shrinkage rate	流动 : 3.20 到 4.60 mm	内部方法	0.60 - 0.90 %
		shrinkage rate	横向流动 : 1.50 到 3.20 mm	内部方法	0.50 - 0.80 %
		shrinkage rate	shrinkage rate	横向流动 : 3.20 到 4.60 mm	内部方法	0.80 - 1.1 %
Water absorption rate	24 hr	ASTM D570	0.070 %

Electrical performance	Test Condition	Test Method	Test Result
volume resistivity		ASTM D257	1.0E+15 ohms·cm
dielectric strength	1.60 mm, in Oil	ASTM D149	25 KV/mm
dielectric strength	dielectric strength	3.20 mm, in Air	ASTM D149	19 KV/mm
dielectric constant	100 Hz	ASTM D150	3.60
dielectric constant	dielectric constant	1 MHz	ASTM D150	3.40
Dissipation Factor	100 Hz	ASTM D150	2.0E-3
Dissipation Factor	Dissipation Factor	1 MHz	ASTM D150	0.016
arc resistance		ASTM D495	PLC 6
Compared to the Leakage Tracking Index (CTI)		UL 746	PLC 3
High arc combustion index (HAI)		UL 746	PLC 0
High Voltage Arc Traceability Rate (HVTR)		UL 746	PLC 4
Hot wire ignition (HWI)		UL 746	PLC 3

injection	Test Condition	Test Method	Test Result
drying temperature			120 °C
drying time			3.0 to 4.0 hr
Suggested maximum moisture content			0.020 %
Suggested injection volume			40 to 80 %
Temperature at the rear of the barrel			240 to 255 °C
Temperature in the middle of the barrel			245 to 260 °C
Temperature at the front of the material cylinder			250 to 265 °C
Spray nozzle temperature			245 to 260 °C
Processing (melt) temperature			250 to 265 °C
mold temperature			65 to 90 °C
Back pressure			0.300 to 0.700 Mpa
screw speed			50 to 80 rpm
Exhaust hole depth			0.025 to 0.038 mm

mechanical properties	Test Condition	Test Method	Test Result
tensile strength	断裂	ASTM D638	93.0 Mpa
flexural modulus	50.0 mm 跨距	ASTM D790	5200 Mpa
bending strength	断裂, 50.0 mm 跨距	ASTM D790	140 Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top