Technical Data Sheet Compareoptical performance Test Condition Test Method Test Result Refractive index ASTM D542 1.586 transmissivity 2540μm ASTM D1003 85.0 % turbidity 2540μm ASTM D1003 1.0 %
impact performance Test Condition Test Method Test Result Impact strength of cantilever beam gap ASTM D1822 525 kJ/m² Suspended wall beam without notch impact strength 23°C ASTM D4812 3200 J/m Dart impact 23°C ASTM D3029 169 J
flammability Test Condition Test Method Test Result UL flame retardant rating 1.47mm UL 94 V-2 UL flame retardant rating 3.00mm UL 94 V-0 Extreme Oxygen Index ISO 4589-2 35 % Radiation board grade UL YES
mechanical properties Test Condition Test Method Test Result tensile strength Yield ASTM D638 62.1 Mpa tensile strength Break ASTM D638 55.8 Mpa elongation Yield ASTM D638 7.0 % elongation Break ASTM D638 90 % Bending modulus 50.0mmSpan ASTM D790 2240 Mpa bending strength Yield,50.0mmSpan ASTM D790 91.0 Mpa Taber abraser 1000Cycles,1000g,CS-17Wheel ASTM D1044 10.0 mg
thermal performance Test Condition Test Method Test Result RTI UL 746 130 °C RTI Imp UL 746 120 °C RTI Elec UL 746 130 °C thermal conductivity ASTMC177 0.19 W/m/K Linear coefficient of thermal expansion MD:-40to95°C ASTME831 6.8E-05 cm/cm/°C Vicat softening temperature ASTM D15256 152 °C Hot deformation temperature 1.8MPa,Unannealed,6.40mm ASTM D648 132 °C Hot deformation temperature 0.45MPa,Unannealed,6.40mm ASTM D648 138 °C
Physical properties Test Condition Test Method Test Result Water absorption rate Equilibrium,100°C ASTM D570 0.58 % Water absorption rate Equilibrium,23°C ASTM D570 0.35 % Water absorption rate 24hr ASTM D570 0.15 % Shrinkage rate MD:3.20mm Internal Method 0.50-0.70 % melt mass-flow rate 300°C/1.2kg ASTM D1238 10 g/10min Specific volume ASTM D792 0.835 cm³/g
Electrical performance Test Condition Test Method Test Result Dissipation factor 1MHz ASTM D150 0.010 Arc resistance ASTM D495 PLC7 Compared to the anti leakage trace index CTI UL 746 PLC 2 High arc combustion index HAI UL 746 PLC 3 Dissipation factor 60Hz ASTM D150 9E-04 Dissipation factor 50Hz ASTM D150 9E-04 Dielectric constant 1MHz ASTM D150 2.96 Dielectric constant 60Hz ASTM D150 3.01 Dielectric constant 50Hz ASTM D150 3.01 Dielectric strength 3.20mm,inAir ASTM D149 17 KV/mm Volume resistivity ASTM D257 >1.0E+17 ohms·cm High voltage arc tracing rate HVTR UL 746 PLC 3 Hot wire ignition HWI UL 746 PLC 2
hardness Test Condition Test Method Test Result Rockwell hardness R-Scale ASTM D785 118 Rockwell hardness M-Scale ASTM D785 70
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.