Material Properties:enhance｜Glass fiber reinforced｜Low temperature resistance
Application Areas:Automotive sector｜Electrical appliances｜Electronic field｜Electrical field｜Automotive interior parts｜Automotive External Parts
Color:--
Grade:Enhanced level

Technical Data Sheet Compare

thermal performance	Test Condition	Test Method	Test Result
Heat Deflection Temperature	1.8 MPa, 未退火, 3.20 mm	ASTM D648	135 °C
Heat Deflection Temperature	Heat Deflection Temperature	1.8 MPa, 未退火, 4.00 mm, 64.0 mm 跨距9	ISO 75-2/Af	134 °C
vicat	--	ASTM D152510	145 °C
	vicat	--	ISO 306/B50	144 °C
	vicat	vicat	--	ISO 306/B120	146 °C
ball-indentation hardness	73 到 77°C	IEC 60695-10-2	通过
Linear coefficient of thermal expansion	流动 : -40 到 40°C	ASTM E831	4.1E-5 cm/cm/°C
	Linear coefficient of thermal expansion	横向 : -40 到 40°C	ASTM E831	6.9E-5 cm/cm/°C
	Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	横向 : -40°C	ISO 11359-2	6.9E-5 cm/cm/°C

Impact resistance	Test Condition	Test Method	Test Result
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	15 kJ/m²
Charpy Notched Impact Strength	Charpy Notched Impact Strength	23°C	ISO 179/1eA	25 kJ/m²
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Impact strength of simply supported beam without notch	Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂
Suspended wall beam without notch impact strength	Suspended wall beam without notch impact strength	23°C	ISO 180/1U	无断裂
Dart impact	23°C, Total Energy	ASTM D3763	40.0 J

Physical properties	Test Condition	Test Method	Test Result
melt mass-flow rate	300°C/1.2 kg	ASTM D1238	11 g/10 min
Melt volume flow rate	300°C/1.2 kg	ISO 1133	10.0 cm3/10min
shrinkage rate	3.20 mm，Flow	内部方法	0.20 - 0.60 %
Water absorption rate	饱和, 23°C	ISO 62	0.12 %
Water absorption rate	Water absorption rate	平衡, 23°C, 50% RH	ISO 62	0.46 %

Electrical performance	Test Condition	Test Method	Test Result
Surface Resistivity		ASTM D257	2.9E+17 ohms
volume resistivity		ASTM D257	1.8E+17 ohms·cm
dielectric strength	1.60 mm, in Oil	ASTM D149	32 KV/mm
dielectric constant	1 MHz	ASTM D150	3.04
dielectric constant	dielectric constant	1.90 GHz	内部方法	2.95
Dissipation Factor	1 MHz	ASTM D150	8.6E-3
Dissipation Factor	Dissipation Factor	1.90 GHz	内部方法	5.7E-3

injection	Test Condition	Test Method	Test Result
drying temperature			120 °C
drying time			3.0 to 4.0 hr
Suggested maximum moisture content			0.020 %
Suggested injection volume			40 to 60 %
Temperature at the rear of the barrel			290 to 310 °C
Temperature in the middle of the barrel			300 to 320 °C
Temperature at the front of the material cylinder			310 to 330 °C
Spray nozzle temperature			305 to 325 °C
Processing (melt) temperature			310 to 330 °C
mold temperature			80 to 115 °C
Back pressure			0.300 to 0.700 Mpa
screw speed			40 to 70 rpm
Exhaust hole depth			0.025 to 0.076 mm

mechanical properties	Test Condition	Test Method	Test Result
Tensile modulus	--2	ASTM D638	3300 Mpa
Tensile modulus	Tensile modulus	--	ISO 527-2/1	3300 Mpa
tensile strength	屈服3	ASTM D638	53.0 Mpa
	tensile strength	屈服	ISO 527-2/5	55.0 Mpa
		tensile strength	断裂3	ASTM D638	44.0 Mpa
		tensile strength	tensile strength	断裂	ISO 527-2/5	43.0 Mpa
elongation	屈服3	ASTM D638	4.5 %
	elongation	屈服	ISO 527-2/5	4.5 %
		elongation	断裂3	ASTM D638	20 %
		elongation	elongation	断裂	ISO 527-2/5	13 %
flexural modulus	50.0 mm 跨距4	ASTM D790	3200 Mpa
flexural modulus	flexural modulus	--5	ISO 178	3300 Mpa
bending strength	--5,6	ISO 178	90.0 Mpa
bending strength	bending strength	屈服, 50.0 mm 跨距4	ASTM D790	95.0 Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top