Impact strength of simply supported beam without notch
23°C
ISO 179/1eU
95 kJ/m²
Impact strength of simply supported beam without notch
-30°C
ISO 179/1eU
100 kJ/m²
flammability
Test Condition
Test Method
Test Result
UL flame retardant rating
1.6mm
UL 94
HB
UL flame retardant rating
3.2mm
UL 94
HB
Burning wire flammability index
2.0mm
IEC 60695-2-12
600 °C
Extreme Oxygen Index
ISO 4589-2
27 %
BurningBehavior
>1.00mm
ISO 3795
passed
mechanical properties
Test Condition
Test Method
Test Result
Tensile modulus
23°C
ISO 527-2/1
16000 Mpa
tensile strength
Break,23°C
ISO 527-2/5
230 Mpa
Tensile strain
Break,23°C
ISO 527-2/5
2.6 %
Bending modulus
23°C
ISO 178/A
14000 Mpa
bending strength
3.5%Strain
ISO 178/A
-- Mpa
bending strength
23°C
ISO 178
360 Mpa
bending strength
FlexuralStrainatFlexuralStrength5(23°C)
3.0 %
thermal performance
Test Condition
Test Method
Test Result
Linear coefficient of thermal expansion
TD:23to55°C
ISO 11359-2
8E-05 cm/cm/°C
Linear coefficient of thermal expansion
MD:23to55°C
ISO 11359-2
2E-05 cm/cm/°C
Melting temperature
ISO 11357-3
261 °C
Ball Pressure Test
258°C
IEC 60695-10-2
Pass
Vicat softening temperature
--
ISO 306/B120
>230 °C
Vicat softening temperature
--
ISO 306/B50
>230 °C
Hot deformation temperature
1.8MPa,Unannealed
ISO 75-2/A
250 °C
Hot deformation temperature
0.45MPa,Unannealed
ISO 75-2/B
250 °C
Physical properties
Test Condition
Test Method
Test Result
Water absorption rate
Equilibrium,23°C,50%RH
ISO 62
1.4 %
Water absorption rate
Saturation,23°C
ISO 62
4.0 %
Shrinkage rate
MD:120°C,2hr,3.00mm3
ISO 2577
0.020 %
Shrinkage rate
MD:300°C,3.00mm2
ISO 2577
0.23 %
Shrinkage rate
TD:120°C,2hr,3.00mm3
ISO 294-4
0.040 %
Shrinkage rate
TD:300°C,3.00mm2
ISO 2577
0.90 %
Apparent density
ISO 60
0.70 g/cm³
Electrical performance
Test Condition
Test Method
Test Result
Relative permittivity
23°C,1MHz
IEC 60250
4.00
Relative permittivity
23°C,100Hz
IEC 60250
4.50
Dielectric strength
23°C,1.00mm
IEC 60243-1
40 KV/mm
Volume resistivity
23°C
IEC 60093
1E+15 ohms·cm
Surface resistivity
IEC 60093
1E+13 ohms
Dissipation factor
23°C,100Hz
IEC 60250
9E-03
Dissipation factor
23°C,1MHz
IEC 60250
0.015
Compared to the anti leakage trace index
SolutionA
IEC 60112
V
hardness
Test Condition
Test Method
Test Result
Ball Pressure Test
ISO 2039-1
246 Mpa
film
Test Condition
Test Method
Test Result
Thin film puncture strength
--6
ISO 6603-2
3.60 J
Thin film puncture strength
--7
ISO 6603-2
2.80 J
Thin film puncture strength
--6
ISO 6603-2
1160 N
Thin film puncture strength
--7
ISO 6603-2
1050 N
Supplementary Information
Test Condition
Test Method
Test Result
ISO Shortcut
ISO 1874
PA66.GHR.14-160.GF50
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.