thermal performance	Test Condition	Test Method	Test Result
Heat Deflection Temperature	1.8 MPa, 未退火	ISO 75-2/A	245 °C
melting temperature		ISO 11357-3	295 °C
Linear coefficient of thermal expansion	流动 : 23 到 55°C	ISO 11359-2	1.5E-5 cm/cm/°C
Linear coefficient of thermal expansion	Linear coefficient of thermal expansion	横向 : 23 到 55°C	ISO 11359-2	5.0E-5 到 6.0E-5 cm/cm/°C
specific heat			1300 J/kg/°C
thermal conductivity		DIN 52612	0.28 W/m/K
Temperature index - at 50% loss of tensile strength	--5	IEC 60216	160 °C
Temperature index - at 50% loss of tensile strength	Temperature index - at 50% loss of tensile strength	--6	IEC 60216	135 °C
maximum service temperature	短周期操作		270 °C

flammability	Test Condition	Test Method	Test Result
Flammability level		UL 94	HB
Polymer Abbreviation			PA6T/6-GF35

Impact resistance	Test Condition	Test Method	Test Result
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	100 kJ/m²

Physical properties	Test Condition	Test Method	Test Result
Apparent density			0.70 g/cm³
shrinkage rate	横向流量	ISO 294-4	1.0 %
shrinkage rate	shrinkage rate	流量	ISO 294-4	0.30 %
Water absorption rate	饱和, 23°C	ISO 62	4.3 to 5.3 %
Water absorption rate	Water absorption rate	平衡, 23°C, 50% RH	ISO 62	0.80 to 1.2 %
viscosity number	96% H2SO4	ISO 307	130 cm³/g
Mold Shrinkage - Constrained			0.35 %

Electrical performance	Test Condition	Test Method	Test Result
Surface Resistivity		IEC 60093	-- ohms
volume resistivity		IEC 60093	1.0E+15 ohms·cm
dielectric strength		IEC 60243-1	33 KV/mm
relative permittivity	1 MHz	IEC 60250	4.20
Dissipation Factor	1 MHz	IEC 60250	0.020
Compared to the Leakage Tracking Index (CTI)	解决方案 A	IEC 60112	V

injection	Test Condition	Test Method	Test Result
drying temperature			110 °C
drying time			8.0 hr
Suggested maximum moisture content			0.15 %
Hopper temperature			80 °C
Temperature at the rear of the barrel			300 °C
Temperature in the middle of the barrel			310 °C
Temperature at the front of the material cylinder			320 °C
Spray nozzle temperature			320 °C
Processing (melt) temperature			310 to 330 °C
mold temperature			80 to 120 °C
Residence Time			< 5.0 min
screw speed			< 18 m/min

mechanical properties	Test Condition	Test Method	Test Result
Tensile modulus		ISO 527-2	12000 Mpa
tensile strength	断裂	ISO 527-2	210 Mpa
Tensile strain	断裂	ISO 527-2	3.0 %
Tensile creep modulus	1000 hr	ISO 899-1	-- Mpa

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.

Get App

Top