
MPR 3075 NC USA Advanced
کاربردهای معمول:
Pipeline enveloping molding coating application cable sheath profile soft handle weather resistant sealing strip fabric coating gasket handle seal pipe fitting universal wire and cable application
توصیف محصول
گواهینامهها(0)
جدول خواص
توصیف محصول
| کاربردهای معمول: | Pipeline | enveloping molding | coating application | cable sheath | profile | soft handle | weather resistant sealing strip | fabric coating | gasket | handle | seal | pipe fitting | universal | wire and cable application |
گواهینامهها
No Data...
برگه داده فنی
| elastomer | شرایط آزمون | روش آزمون | نتیجه آزمون | واحد آزمایش |
|---|---|---|---|---|
| Stretch permanent deformation | ASTM D412 | 11 | % | |
| tensile strength | 100%Strain,1.90mm2 | ASTM D412 | 5.90 | MPa |
| elongation | Break,125°C,1.90mm4 | ISO 188 | 350 | % |
| tear strength | 1.90mm | ASTM D624 | 49.0 | kN/m |
| Permanent compression deformation | 24°C,22hr | ASTM D395B | 23 | % |
| 100°C,22hr | ASTM D395B | 67 | % | |
| 24°C,22hr | ISO 815 | 23 | % | |
| 100°C,22hr | ISO 815 | 67 | % | |
| Clash Mountain Module | -17°C | ASTM D1043 | 68.9 | MPa |
| tensile strength | 100%Strain,125°C,1.90mm4 | ASTM D573 | 6.60 | MPa |
| 100%Strain,1.90mm2 | ISO 37 | 5.90 | MPa | |
| elongation | Break,1.90mm2 | ASTM D412 | 360 | % |
| tensile strength | Yield,125°C,1.90mm4 | ISO 188 | 10.5 | MPa |
| elongation | Break,125°C,1.90mm4 | ASTM D573 | 350 | % |
| tensile strength | Yield,1.90mm2 | ISO 37 | 9.80 | MPa |
| Yield,125°C,1.90mm4 | ASTM D573 | 10.5 | MPa | |
| Yield,1.90mm2 | ASTM D412 | 9.80 | MPa | |
| 100%Strain,125°C,1.90mm4 | ISO 188 | 6.60 | MPa | |
| elongation | Break,1.90mm2 | ISO 37 | 360 | % |
| mechanical properties | شرایط آزمون | روش آزمون | نتیجه آزمون | واحد آزمایش |
| TorsionModulus | 24°C,1.90mm | ASTM D1043 | 3.40 | MPa |
| -20°C,1.90mm | ASTM D1043 | 128 | MPa | |
| Taber abraser | 1000Cycles,1000g,CS-17Wheel | ASTM D1044 | <1.00 | mg |
| thermal performance | شرایط آزمون | روش آزمون | نتیجه آزمون | واحد آزمایش |
| Brittle temperature | ISO 812 | -30.0 | °C | |
| ASTM D746 | -30.0 | °C | ||
| Physical properties | شرایط آزمون | روش آزمون | نتیجه آزمون | واحد آزمایش |
| density | ISO 2781 | 1.35 | g/cm³ | |
| MeltViscosity | 190°C,300sec^-1 | ASTM D3835 | 840 | Pa·s |
| density | ASTM D471 | 1.35 | g/cm³ | |
| hardness | شرایط آزمون | روش آزمون | نتیجه آزمون | واحد آزمایش |
| DurometerHardness | ShoreA,1.90mm,CompressionMolded | ASTM D2240 | 76 | |
| Shore hardness | ShoreA,1.90mm,CompressionMolded | ISO 868 | 76 | |
| aging | شرایط آزمون | روش آزمون | نتیجه آزمون | واحد آزمایش |
| Hardness change rate in the air | ShoreA,125°C,168hr | ASTM D573 | -2.0 | |
| Shore hardness | ShoreA,125°C,168hr | ISO 188 | -2.0 | |
| Volume change | 27°C,168hr,inReferenceFuelB | ASTM D471 | 36 | % |
| 100°C,168hr,inASTM#1Oil | ASTM D471 | -6.0 | % | |
| 100°C,168hr,inIRM903Oil | ASTM D471 | 29 | % | |
| 100°C,168hr,在水中 | ISO 1817 | 13 | % | |
| 100°C,168hr,inASTM#1Oil | ISO 1817 | -6.0 | % | |
| 27°C,168hr,inReferenceFuelB | ISO 1817 | 36 | % | |
| 100°C,168hr,在水中 | ASTM D471 | 13 | % | |
| 100°C,168hr,inIRM903Oil | ISO 1817 | 29 | % |
نکات مهم: Plas.com دادههای برگه فنی را از تولیدکنندگان مواد جمعآوری کرده است. Plas.com تمام تلاش خود را برای افزایش دقت دادهها انجام میدهد، اما هیچ مسئولیتی در قبال دادهها ندارد. اکیداً توصیه میشود که صحت دادهها را با تولیدکنندگان مواد تأیید کنید پیش از آنکه تصمیم نهایی بگیرید.