برگه داده فنی
physical property | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
density | | ASTM D792 | 1.25 g/cm³ |
melt mass-flow rate | 300°C/1.2 kg | ASTM D1238 | 18 g/10 min |
Shrinkage rate | 23°C, 3.20 mm, 注塑,Flow | ASTM D955 | 0.20 - 0.40 % |
hardness | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
Rockwell hardness | R 级, 23°C, 注塑 | ASTM D785 | 124 |
flammability | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
UL flame retardant rating | 1.5 mm | UL 94 | V-0 |
UL flame retardant rating | 3.0 mm | UL 94 | V-0 |
Mechanical properties | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
tensile strength | 屈服, 23°C, 3.20 mm, 注塑 | ASTM D638 | 83.4 Mpa |
Flexural modulus | 23°C, 3.20 mm, 注塑 | ASTM D790 | 3920 Mpa |
bending strength | 23°C, 3.20 mm, 注塑 | ASTM D790 | 137 Mpa |
Impact resistance | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
Impact strength of cantilever beam gap | 23°C, 3.20 mm, 注塑 | ASTM D256 | 78 J/m |
injection | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
drying temperature | | | 100 to 200 °C |
drying time | | | 3.0 to 5.0 hr |
Suggested maximum moisture content | | | 0.020 % |
Temperature at the rear of the barrel | | | 270 to 300 °C |
Temperature in the middle of the barrel | | | 280 to 310 °C |
Temperature at the front of the material cylinder | | | 290 to 330 °C |
Spray nozzle temperature | | | 290 to 330 °C |
Processing (melt) temperature | | | 300 to 340 °C |
Temperature | | | 90 to 120 °C |
Back pressure | | | 0.981 to 3.92 Mpa |
screw speed | | | 40 to 70 rpm |
Thermal performance | شرایط آزمون | روش آزمون | نتیجه آزمون |
---|
Heat distortion temperature | 1.8 MPa, 未退火, 6.40 mm, 注塑,HDT | ASTM D648 | 138 °C |
RTI Elec | | UL 746 | 120 °C |
RTI Imp | | UL 746 | 90.0 °C |
RTI | | UL 746 | 105 °C |
نکات مهم: Plas.com دادههای برگه فنی را از تولیدکنندگان مواد جمعآوری کرده است. Plas.com تمام تلاش خود را برای افزایش دقت دادهها انجام میدهد، اما هیچ مسئولیتی در قبال دادهها ندارد. اکیداً توصیه میشود که صحت دادهها را با تولیدکنندگان مواد تأیید کنید پیش از آنکه تصمیم نهایی بگیرید.