مقایسه مواد
اطلاعات محصول
نام محصول
نام برند
کاربردها
ویژگیها
گواهینامهها

PC 301-4 SUMITOMO JAPAN
SD POLYCA™
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
برگههای اطلاعات پلاستیک
hardness | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
Rockwell hardness | R -Sale | ISO 2039-2 | 118 |
thermal performance | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
Hot deformation temperature | 1.8 MPa, Unannealed | ISO 75-2/Af | 130 °C |
Linear coefficient of thermal expansion | Across Flow | ISO 11359-2 | 7.0E-5 cm/cm/°C |
Flow | ISO 11359-2 | 7.0E-5 cm/cm/°C |
mechanical properties | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
Bending modulus | ISO 178 | 2300 Mpa | |
bending strength | ISO 178 | 92.0 Mpa | |
Tensile modulus | ISO 527-2 | 2300 Mpa | |
Tensile strain | Break | ISO 527-2 | 110 % |
tensile strength | Yield | ISO 527-2 | 60.0 Mpa |
Electrical performance | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
Compared to the anti leakage trace index | IEC 60112 | PLC 2 | |
Dielectric strength | 1.00 mm | IEC 60243-1 | 31 KV/mm |
Dissipation factor | 2.00 mm, 100 Hz | IEC 60250 | 1.0E-3 |
2.00 mm, 1 MHz | IEC 60250 | 0.090 | |
Relative permittivity | 2.00 mm, 1 MHz | IEC 60250 | 3.00 |
2.00 mm, 100 Hz | IEC 60250 | 3.00 | |
Surface resistivity | IEC 60093 | > 1.0E+15 ohms | |
Volume resistivity | IEC 60093 | 3.0E+16 ohms·cm |
Physical properties | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
melt mass-flow rate | 300°C/1.2 kg | ISO 1133 | 4.0 g/10 min |
Melt Volume Flow Rate (MVR) | 300°C/1.2 kg | ISO 1133 | 4.00 cm3/10min |
Shrinkage rate | Flow | Internal Method | 0.50 - 0.70 % |
Across FlowFlow | Internal Method | 0.50 - 0.70 % | |
Water absorption rate | 24 hr, 23°C | ISO 62 | 0.20 % |
impact performance | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
Impact strength of simply supported beam without notch | 23°C | ISO 179 | 无断裂 |
flammability | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
UL flame retardant rating | 3.0 mm | UL 94 | HB |
0.44 mm | UL 94 | V-2 | |
0.75 mm | UL 94 | V-2 | |
1.5 mm | UL 94 | HB |
optical performance | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
Refractive index | ISO 489 | 1.585 | |
transmissivity | 2000 μm | ISO 13468 | 89.0 % |
turbidity | 2000 μm | ISO 14782 | 0.40 % |
injection | شرایط آزمون | روش آزمون | SUMITOMO JAPAN/301-4 |
---|---|---|---|
drying temperature | 125 °C | ||
drying time | 4.0 to 6.0 hr | ||
Mold temperature | 70 to 100 °C | ||
Screw speed | 60 to 100 rpm | ||
Spray nozzle temperature | 310 to 330 °C | ||
Temperature at the front of the material cylinder | 310 to 330 °C | ||
Temperature at the rear of the barrel | 280 to 300 °C | ||
Temperature in the middle of the barrel | 290 to 310 °C |