plas
ورود | ثبت‌نام
دسته‌بندی‌هاهمه
مواد اولیه پلاستیک
پلاستیک‌های اصلاح‌شده
افزودنی‌های پلاستیکی
مستربچ رنگی
برگه‌های اطلاعات پلاستیک
اخبار پلاستیک
درباره ما

مقایسه مواد

اطلاعات محصول
نام محصول
نام برند
کاربردها
ویژگی‌ها
گواهی‌نامه‌ها
PBT 310SE0-BK SABIC INNOVATIVE JAPAN
VALOX™ 
محور,پوسته,سوئیچ,قطعات لوازم خانگی,حوزه الکترونیک,زمینه برق,عمومی
عقب نشینی
UL
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--

برگه‌های اطلاعات پلاستیک

hardnessشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Ball Pressure TestH 358/30ISO 2039-1105 Mpa
Rockwell hardnessR -SaleISO 2039-2120
R-ScaleASTM D785117
thermal performanceشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Ball Pressure Test123 to 127°CIEC 60695-10-2通过
Hot deformation temperature1.8MPa,Unannealed,6.40mmASTM D64854.4 °C
1.8 MPa, Unannealed, 4.00 mm, 100 mm Span10ISO 75-2/Ae60.0 °C
1.8 MPa, Unannealed, 6.40 mmASTM D64871.0 °C
1.8 MPa, Unannealed, 3.20 mmASTM D64874.0 °C
0.45MPa,Unannealed,6.40mmASTM D648154 °C
0.45 MPa, Unannealed, 4.00 mm, 100 mm Span10ISO 75-2/Be150 °C
1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span9ISO 75-2/Af73.0 °C
0.45 MPa, Unannealed, 6.40 mmASTM D648162 °C
Linear coefficient of thermal expansionFlow : -40 to 40°CASTM E8317.9E-5 cm/cm/°C
Flow : -40 to 40°CISO 11359-27.6E-5 cm/cm/°C
Flow : 60 to 138°CASTM E8311.3E-4 cm/cm/°C
Across Flow : -40°CISO 11359-27.3E-5 cm/cm/°C
Across Flow : 23 to 60°CISO 11359-21.0E-4 cm/cm/°C
MD：-40to40°CASTME8318.1E-05 cm/cm/°C
Across Flow : -40 to 40°CASTM E8317.9E-5 cm/cm/°C
Flow : 23 to 60°CISO 11359-21.0E-4 cm/cm/°C
MD：60to138°CASTME8311.4E-04 cm/cm/°C
RTIUL 746140 °C
RTI ElecUL 746120 °C
RTI ImpUL 746120 °C
RTI StrUL 746140 °C
thermal conductivityISO 83020.24 W/m/K
Vicat softening temperature--ISO 306/A50212 °C
--ASTM D152511170 °C
mechanical propertiesشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Bending modulus--6ISO 1782600 Mpa
50.0 mm Span5ASTM D7902620 Mpa
50.0mmSpanASTM D7902340 Mpa
bending strengthYield,50.0mmSpanASTM D79082.7 Mpa
--6,7ISO 17890.0 Mpa
Break,50.0mmSpanASTM D79082.7 Mpa
Yield, 50.0 mm Span5ASTM D790101 Mpa
elongationYieldISO 527-2/505.0 %
Yield4ASTM D6385.0 %
BreakASTM D638300 %
Break4ASTM D63818 %
BreakISO 527-2/5018 %
Taber abraser1000 Cycles, 1000 g, CS-17 WheelInternal Method19.0 mg
Tensile modulus--3ASTM D6382820 Mpa
--ISO 527-2/12800 Mpa
tensile strengthYieldASTM D63851.7 Mpa
YieldISO 527-2/5058.0 Mpa
BreakISO 527-2/5040.0 Mpa
Break4ASTM D63852.0 Mpa
BreakASTM D63851.7 Mpa
Yield4ASTM D63858.0 Mpa
Electrical performanceشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Arc resistanceASTM D495PLC 5
Compared to the anti leakage trace indexUL 746PLC 3
CTIUL 746PLC 0
Solution BIEC 60112 V
--IEC 60112 V
Dielectric constant100HzASTM D1503.30
1MHzASTM D1503.10
Dielectric strength1.00 mm12IEC 60243-118 KV/mm
1.60 mm, in OilASTM D14924 KV/mm
3.20 mm, in AirASTM D14918 KV/mm
1.60mm,inAirASTM D14923 KV/mm
3.20mm,inAirASTM D14916 KV/mm
3.20 mm, in OilIEC 60243-117 KV/mm
3.20mm,in OilASTM D14916 KV/mm
0.800 mm, in OilIEC 60243-135 KV/mm
1.60 mm, in OilIEC 60243-125 KV/mm
1.60mm,in OilASTM D14923 KV/mm
Dissipation factor50 HzIEC 602501.0E-3
60 HzIEC 602501.0E-3
100 HzIEC 602502.0E-3
1MHzASTM D1500.020
1 MHzIEC 602500.013
100HzASTM D1502E-03
High arc combustion indexUL 746PLC 0
High Voltage Arc Resistance Index (HVAR) (PLC)UL 746PLC 6
High voltage arc tracing rateHVTRUL 746PLC 1
UL 746PLC 4
Hot wire ignitionUL 746PLC 2
Relative permittivity50 HzIEC 602502.90
1 MHzIEC 602502.80
100 HzIEC 602503.10
60 HzIEC 602502.90
Surface resistivityIEC 60093> 1.0E+15 ohms
Volume resistivityIEC 60093> 1.0E+15 ohms·cm
ASTM D257>4.0E+16 ohms·cm
Physical propertiesشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
melt mass-flow rate250°C/2.16 kgASTM D12388.6 g/10 min
Melt viscosityInternal Method600 Pa·s
Melt Volume Flow Rate (MVR)250°C/2.16 kgISO 11338.00 cm3/10min
Shrinkage rateFlow : 0.750 to 2.30 mmInternal Method0.90 - 1.6 %
TD：--2Internal Method1.0-1.7 %
Across FlowFlow : 2.30 to 4.60 mmInternal Method1.6 - 2.4 %
Across FlowFlow : 0.750 to 2.30 mmInternal Method1.0 - 1.7 %
Flow : 2.30 to 4.60 mmInternal Method1.5 - 2.3 %
MD：--2Internal Method0.90-1.6 %
MD：--3Internal Method1.5-2.3 %
Flow : 3.20 mmInternal Method1.5 - 2.3 %
Flow 2Internal Method1.1 - 1.8 %
TD：--3Internal Method1.6-2.4 %
Across FlowFlow 2Internal Method0.90 - 1.9 %
Specific volumeASTM D7920.770 cm³/g
Water absorption rateSaturation, 23°CISO 620.36 %
Equilibrium, 23°C, 50% RHISO 620.080 %
24hrASTM D5700.080 %
impact performanceشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Dart impact23°CASTM D302940.7 J
23°C, Total EnergyASTM D3763200 J
23°C6ASTM D302940.7 J
Impact strength of simply supported beam without notch-30°CISO 179/1eU无断裂
23°CISO 179/1eU无断裂
Suspended wall beam without notch impact strength-30°C9ISO 180/1U无断裂
23°CASTM D4812无断裂
flammabilityشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Burning wire flammability index1.0 mmIEC 60695-2-12960 °C
Extreme Oxygen IndexISO 4589-230 %
UL flame retardant rating0.71 mmUL 94V-0
3.0 mmUL 945VA
1.5mmUL 94HB
injectionشرایط آزمونروش آزمونSABIC INNOVATIVE JAPAN/310SE0-BK
Back pressure0.300 to 0.700 Mpa
drying temperature120 °C
drying time3.0 to 4.0 hr
Exhaust hole depth0.013 to 0.025 mm
Mold temperature50 to 75 °C
Processing (melt) temperature245 to 260 °C
Screw speed50 to 100 rpm
Spray nozzle temperature240 to 255 °C
Suggested injection volume40 to 80 %
Suggested maximum moisture content0.020 %
Temperature at the front of the material cylinder245 to 260 °C
Temperature at the rear of the barrel230 to 250 °C
Temperature in the middle of the barrel240 to 255 °C

تماس با ما

دریافت اپلیکیشن

Top