مقایسه مواد
اطلاعات محصول
نام محصول
نام برند
کاربردها
ویژگیها
گواهینامهها

PC DX11355-BKNAT SABIC INNOVATIVE NANSHA
LNP™ THERMOCOMP™
قطعات خودرو,قطعات الکترونیکی
ثبات حرارتی,جریان بالا
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
برگههای اطلاعات پلاستیک
thermal performance | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
Hot deformation temperature | 1.8 MPa, Unannealed, 3.20 mm | ASTM D648 | 114 °C |
Linear coefficient of thermal expansion | 垂直 : -40 to 40°C | 0.000067 cm/cm/°C | |
Flow : -40 to 40°C | 0.000062 cm/cm/°C | ||
RTI | UL 746B | 80 °C | |
RTI Elec | UL 746B | 80 °C | |
RTI Imp | UL 746B | 80 °C |
mechanical properties | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
Bending modulus | 50.0 mm Span | ASTM D790 | 2400 Mpa |
bending strength | Yield, 50.0 mm Span | 90 Mpa | |
Break, 50.0 mm Span | 89 Mpa | ||
elongation | Yield | 5.4 % | |
Break | 70 % | ||
Tensile modulus | ASTM D638 | 2600 Mpa | |
tensile strength | Break | 52 Mpa | |
Yield | 58 Mpa |
Electrical performance | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
Dissipation factor | 1.00 GHz | IEC 60250 | 0.007 |
Relative permittivity | 1.00 GHz | IEC 60250 | 2.92 |
Physical properties | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
melt mass-flow rate | 300°C/1.2 kg | ASTM D1238 | 12 g/10 min |
Shrinkage rate | Flow : 24hr | 0.5 % | |
Across FlowFlow : 24hr | 0.5 % | ||
Water absorption rate | 24 hr, 23°C, 50% RH | ASTM D570 | 0.01 % |
impact performance | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
Impact strength of cantilever beam gap | 23°C | ASTM D4812 | 2100 J/m |
flammability | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
UL flame retardant rating | 0.60mm | UL 94 | V-0 |
injection | شرایط آزمون | روش آزمون | SABIC INNOVATIVE NANSHA/DX11355-BKNAT |
---|---|---|---|
Back pressure | 0.300 to 0.700 Mpa | ||
drying temperature | 100 to 110 °C | ||
drying time | 3.0 to 4.0 hr | ||
Exhaust hole depth | 0.038 to 0.076 mm | ||
Hopper temperature | 60 to 80 °C | ||
Mold temperature | 60 to 90 °C | ||
Processing (melt) temperature | 275 to 300 °C | ||
Screw speed | 40 to 70 rpm | ||
Spray nozzle temperature | 275 to 300 °C | ||
Suggested injection volume | 30 to 80 % | ||
Suggested maximum moisture content | 0.02 % | ||
Temperature at the front of the material cylinder | 260 to 300 °C | ||
Temperature at the rear of the barrel | 250 to 290 °C | ||
Temperature in the middle of the barrel | 255 to 295 °C |