PC EXL4419-739 PC vs. - Plastic Material Properties Comparison Chart at Plas.com

انتخاب‌گر مواد

ورود

همه

مواد پلاستیکی افزودنی‌ها مستربچ رنگی انتخاب‌گر مواد نمایه قیمت داده‌های معاملاتی اخبار پلاستیک درباره ما

مقایسه مواد

افزودن مدل برای مقایسه

انتخاب محصولات برای مقایسه (1/4)

برجسته کردن تفاوت ها

مخفی کردن موارد مشابه

نام محصول / تولیدکننده / مدل

درجه

قیمت مرجع

PC SABIC INNOVATIVE US EXL4419-739

درجه تزریق

US$ ۳٬۸۲۰ / MT

FOB Guangzhou port, China

injection	شرایط آزمون	روش آزمون	SABIC INNOVATIVE US/EXL4419-739
Back pressure			0.300 to 0.700 Mpa
Temperature at the front of the material cylinder			310 to 330 °C
Screw speed			40 to 70 rpm
Mold temperature			80 to 115 °C
Processing (melt) temperature			310 to 330 °C
Suggested injection volume			40 to 60 %
Suggested maximum moisture content			0.020 %
Spray nozzle temperature			305 to 325 °C
Exhaust hole depth			0.025 to 0.076 mm
drying temperature			120 °C
Temperature in the middle of the barrel			300 to 320 °C
drying time			3.0 to 4.0 hr
Temperature at the rear of the barrel			290 to 310 °C
mechanical properties	شرایط آزمون	روش آزمون	SABIC INNOVATIVE US/EXL4419-739
bending strength	--5,6	ISO 178	90.0 Mpa
elongation	Break	ISO 527-2/5	13 %
Bending modulus	50.0 mm Span4	ASTM D790	3200 Mpa
bending strength	Yield, 50.0 mm Span4	ASTM D790	95.0 Mpa
tensile strength	Yield	ISO 527-2/5	55.0 Mpa
elongation	Yield3	ASTM D638	4.5 %
elongation		Break3	ASTM D638	20 %
tensile strength	Break	ISO 527-2/5	43.0 Mpa
tensile strength		Yield3	ASTM D638	53.0 Mpa
elongation	Yield	ISO 527-2/5	4.5 %
Tensile modulus	--2	ASTM D638	3300 Mpa
Tensile modulus		--	ISO 527-2/1	3300 Mpa
Bending modulus	--5	ISO 178	3300 Mpa
tensile strength	Break3	ASTM D638	44.0 Mpa
Electrical performance	شرایط آزمون	روش آزمون	SABIC INNOVATIVE US/EXL4419-739
Dielectric strength	1.60 mm, in Oil	ASTM D149	32 KV/mm
Surface resistivity		ASTM D257	2.9E+17 ohms
Dissipation factor	1.90 GHz	Internal Method	5.7E-3
Dissipation factor		1 MHz	ASTM D150	8.6E-3
Dielectric constant	1 MHz	ASTM D150	3.04
Volume resistivity		ASTM D257	1.8E+17 ohms·cm
Dielectric constant	1.90 GHz	Internal Method	2.95
thermal performance	شرایط آزمون	روش آزمون	SABIC INNOVATIVE US/EXL4419-739
Linear coefficient of thermal expansion	Across Flow : -40 to 40°C	ASTM E831	6.9E-5 cm/cm/°C
Linear coefficient of thermal expansion		Across Flow : -40°C	ISO 11359-2	6.9E-5 cm/cm/°C
Ball Pressure Test	73 to 77°C	IEC 60695-10-2	通过
Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span9	ISO 75-2/Af	134 °C
Linear coefficient of thermal expansion	Flow : -40 to 40°C	ASTM E831	4.1E-5 cm/cm/°C
Vicat softening temperature	--	ISO 306/B50	144 °C
Hot deformation temperature	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	135 °C
Vicat softening temperature	--	ISO 306/B120	146 °C
Vicat softening temperature		--	ASTM D152510	145 °C
Physical properties	شرایط آزمون	روش آزمون	SABIC INNOVATIVE US/EXL4419-739
Water absorption rate	Saturation, 23°C	ISO 62	0.12 %
Melt Volume Flow Rate (MVR)	300°C/1.2 kg	ISO 1133	10.0 cm3/10min
Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.46 %
Shrinkage rate	3.20 mm，Flow	Internal Method	0.20 - 0.60 %
melt mass-flow rate	300°C/1.2 kg	ASTM D1238	11 g/10 min
impact performance	شرایط آزمون	روش آزمون	SABIC INNOVATIVE US/EXL4419-739
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	无断裂
Suspended wall beam without notch impact strength	23°C	ISO 180/1U	无断裂
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	15 kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	无断裂
Dart impact	23°C, Total Energy	ASTM D3763	40.0 J
Charpy Notched Impact Strength	23°C	ISO 179/1eA	25 kJ/m²
Suspended wall beam without notch impact strength	-30°C	ISO 180/1U	无断裂

Supplier Join

تماس با ما

دریافت اپلیکیشن

Top

منبع‌یابی در PLAS.COM

فروش و تأیید صلاحیت

کاوش مواد

نمایه قیمت