مقایسه مواد
اطلاعات محصول
نام محصول
نام برند
کاربردها
ویژگیها
گواهینامهها

LCP V143XL CELANESE USA
VECTRA®
کاربردهای خودرو,کاربردهای الکتریکی
تقویت فیبر شیشه ای,افزایش
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
برگههای اطلاعات پلاستیک
thermal performance | شرایط آزمون | روش آزمون | CELANESE USA/V143XL |
---|---|---|---|
Hot deformation temperature | 1.8 MPa, Unannealed | ISO 75-2/A | 260 °C |
Linear coefficient of thermal expansion | Across Flow | ISO 11359-2 | 3.1E-5 cm/cm/°C |
Flow | ISO 11359-2 | 8.0E-6 cm/cm/°C | |
Melting temperature | ISO 11357-3 | 335 °C |
mechanical properties | شرایط آزمون | روش آزمون | CELANESE USA/V143XL |
---|---|---|---|
Bending modulus | 23°C | ISO 178 | 15700 Mpa |
bending strength | 23°C | ISO 178 | 225 Mpa |
Tensile modulus | ISO 527-2/1A | 16000 Mpa | |
Tensile strain | Break | ISO 527-2/1A/5 | 1.3 % |
tensile strength | Break | ISO 527-2/1A/5 | 150 Mpa |
Electrical performance | شرایط آزمون | روش آزمون | CELANESE USA/V143XL |
---|---|---|---|
Dielectric strength | IEC 60243-1 | 33 KV/mm | |
Dissipation factor | 1 MHz | IEC 60250 | 0.016 |
Relative permittivity | 1 MHz | IEC 60250 | 3.50 |
Surface resistivity | IEC 60093 | 1.0E+17 ohms | |
Volume resistivity | IEC 60093 | 1.0E+16 ohms·cm |
Physical properties | شرایط آزمون | روش آزمون | CELANESE USA/V143XL |
---|---|---|---|
density | ISO 1183 | 1.67 g/cm³ | |
Shrinkage rate | 横向Flow | ISO 294-4 | 0.60 % |
Flow | ISO 294-4 | 0.30 % | |
Water absorption rate | Saturation, 23°C | ISO 62 | 0.044 % |
Equilibrium, 23°C, 50% RH | ISO 62 | 0.015 % |
impact performance | شرایط آزمون | روش آزمون | CELANESE USA/V143XL |
---|---|---|---|
Impact strength of cantilever beam gap | 23°C | ISO 180/1A | 9.0 kJ/m² |
injection | شرایط آزمون | روش آزمون | CELANESE USA/V143XL |
---|---|---|---|
Back pressure | < 3.00 Mpa | ||
drying temperature | 150 °C | ||
drying time | 4.0 to 24 hr | ||
Hopper temperature | 20 to 30 °C | ||
Injection speed | 快速 | ||
Mold temperature | 80 to 120 °C | ||
Processing (melt) temperature | 335 to 345 °C | ||
Spray nozzle temperature | 335 to 345 °C | ||
Suggested maximum moisture content | 0.010 % | ||
Temperature at the front of the material cylinder | 325 to 335 °C | ||
Temperature at the rear of the barrel | 315 to 325 °C | ||
Temperature in the middle of the barrel | 320 to 330 °C |