برگه داده فنی مقایسهFilling analysis شرایط آزمون روش آزمون نتیجه آزمون Melt density Internal Method 1.48 g/cm³ Thermal conductivity of melt Internal Method 0.35 W/m/K Top out temperature 265 °C Specific Heat Capacity of Melt 1500 J/kg/°C
flammability شرایط آزمون روش آزمون نتیجه آزمون UL flame retardant rating 0.8 mm UL 94 V-0 UL flame retardant rating 1.5 mm UL 94 V-0 Extreme Oxygen Index ISO 4589-2 33 %
mechanical properties شرایط آزمون روش آزمون نتیجه آزمون Tensile modulus ISO 527-2/1A 15000 Mpa tensile strength Break ISO 527-2/1A/5 115 Mpa Tensile strain Break ISO 527-2/1A/5 3.1 % Bending modulus 23°C ISO 178 11000 Mpa bending strength 23°C ISO 178 190 Mpa Compressive stress 1% Strain ISO 604 21.3 Mpa
injection شرایط آزمون روش آزمون نتیجه آزمون drying temperature 150 °C drying time 3.0 hr Suggested maximum moisture content 0.010 % Hopper temperature 20 to 30 °C Temperature at the rear of the barrel 320 to 330 °C Temperature in the middle of the barrel 335 to 345 °C Temperature at the front of the material cylinder 335 to 345 °C Spray nozzle temperature 335 to 345 °C Processing (melt) temperature 325 to 345 °C Mold temperature 80 to 120 °C Back pressure < 3.00 Mpa
thermal performance شرایط آزمون روش آزمون نتیجه آزمون Hot deformation temperature 1.8 MPa, Unannealed ISO 75-2/A 290 °C Melting temperature ISO 11357-3 319 °C Linear coefficient of thermal expansion Flow ISO 11359-2 7.0E-6 cm/cm/°C Linear coefficient of thermal expansion Across Flow ISO 11359-2 6.0E-5 cm/cm/°C
Physical properties شرایط آزمون روش آزمون نتیجه آزمون Shrinkage rate 横向Flow ISO 294-4 0.50 % Shrinkage rate Flow ISO 294-4 0.10 %
Electrical performance شرایط آزمون روش آزمون نتیجه آزمون Surface resistivity IEC 60093 1.0E+15 ohms Volume resistivity IEC 60093 1.0E+15 ohms·cm Dielectric strength IEC 60243-1 45 KV/mm Relative permittivity 1 MHz IEC 60250 3.90 Dissipation factor 1 MHz IEC 60250 0.018 Compared to the anti leakage trace index IEC 60112 PLC 3
نکات مهم: Plas.com دادههای برگه فنی را از تولیدکنندگان مواد جمعآوری کرده است. Plas.com تمام تلاش خود را برای افزایش دقت دادهها انجام میدهد، اما هیچ مسئولیتی در قبال دادهها ندارد. اکیداً توصیه میشود که صحت دادهها را با تولیدکنندگان مواد تأیید کنید پیش از آنکه تصمیم نهایی بگیرید.