Material Comparison

Product Info

Product Name

Brand Name

Usages

Properties

Certificates

PPO PX9406-701 SABIC INNOVATIVE US

NORYL™

Household appliances,Household appliances,Automotive interior parts,Electronic communication accessories,Electronic communication accessories

Flame retardant

Plastic Datasheets

thermal performance	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
Hot deformation temperature	0.45 MPa, Unannealed, 6.40 mm	ASTM D648	133 °C
Hot deformation temperature		1.8 MPa, Unannealed, 6.40 mm	ASTM D648	122 °C
RTI		UL 746	110 °C
RTI Elec		UL 746	110 °C
RTI Imp		UL 746	105 °C
Vicat softening temperature		ASTM D15255	150 °C

mechanical properties	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
Bending modulus	100 mm Span	ASTM D790	2640 Mpa
bending strength	Yield, 100 mm Span	ASTM D790	111 Mpa
elongation	Yield	ASTM D638	9.5 %
elongation		Break	ASTM D638	18 %
tensile strength	Yield	ASTM D638	75.0 Mpa
tensile strength		Break	ASTM D638	55.0 Mpa

Electrical performance	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
Arc resistance		ASTM D495	PLC 6
Compared to the anti leakage trace index		UL 746	PLC 2
Dielectric constant	50 kHz	ASTM D150	2.57
		60 Hz	ASTM D150	2.57
		1 MHz	ASTM D150	2.49
Dielectric strength	3.20 mm, in Oil	ASTM D149	19 KV/mm
Dissipation factor	1 MHz	ASTM D150	2.6E-3
		60 Hz	ASTM D150	5.2E-3
		50 Hz	ASTM D150	5.2E-3
High arc combustion index		UL 746	PLC 0
High voltage arc tracing rate		UL 746	PLC 4
Hot wire ignition		UL 746	PLC 0
Surface resistivity		ASTM D257	> 1.0E+16 ohms
Volume resistivity		ASTM D257	2.0E+16 ohms·cm

Physical properties	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
Outdoor applicability		UL 746C	f2
Shrinkage rate	Flow : 3.20 mm	Internal Method	0.50 - 0.70 %
Shrinkage rate		Across FlowFlow 2	Internal Method	0.50 - 0.70 %
Water absorption rate	24 hr	ASTM D570	0.060 %

impact performance	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
Dart impact	23°C, Energy at Peak	ASTM D3763	42.0 J
Suspended wall beam without notch impact strength	23°C	ASTM D4812	1100 J/m

flammability	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
UL flame retardant rating	0.76 mm	UL 94	V-0

injection	Test Condition	Test Method	SABIC INNOVATIVE US/PX9406-701
Back pressure			0.300 to 0.700 Mpa
drying temperature			105 to 110 °C
drying time			3.0 to 4.0 hr
Exhaust hole depth			0.038 to 0.051 mm
Mold temperature			70 to 100 °C
Processing (melt) temperature			275 to 305 °C
Screw speed			20 to 100 rpm
Spray nozzle temperature			275 to 305 °C
Suggested injection volume			30 to 70 %
Suggested maximum moisture content			0.020 %
Temperature at the front of the material cylinder			265 to 305 °C
Temperature at the rear of the barrel			245 to 295 °C
Temperature in the middle of the barrel			255 to 300 °C

Get App

Top