Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Melt Mass-Flow Rate | 260°C/5.0 kg | ASTM D1238 | 19 | g/10 min |
Modeling Shrinkage - Flow | 3.20 mm | 内部方法 | 0.50 到 0.70 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Modulus | | ASTM D638 | 2270 | Mpa |
Tensile Strength | Yield | ASTM D638 | 57.0 | Mpa |
Tensile Elongation | Yield | ASTM D638 | 5.0 | % |
Tensile Elongation | Break | ASTM D638 | 100 | % |
Flexural Modulus | 50.0 mm Span | ASTM D790 | 2340 | Mpa |
Flexural Strength | Yield, 50.0 mm Span | ASTM D790 | 88.0 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load | 0.45 MPa, Unannealed, 3.20 mm | ASTM D648 | 129 | °C |
Deflection Temperature Under Load | 1.8 MPa, Unannealed, 3.20 mm | ASTM D648 | 112 | °C |
Vicat Softening Temperature | | ISO 306/B50 | 130 | °C |
Coefficient of Linear Thermal Expansion (Flow) | -40 to 40°C | ASTM E831 | 7.2E-5 | cm/cm/°C |
RTI Elec | | UL 746 | 105 | °C |
RTI Imp | | UL 746 | 80.0 | °C |
RTI | | UL 746 | 105 | °C |
Electrical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Comparative Tracking Index | | UL 746 | PLC 2 | |
High Amp Arc Ignition | | UL 746 | PLC 1 | |
Hot-wire Ignition | | UL 746 | PLC 3 | |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Temperature | | | 100 到 110 | °C |
Drying Time | | | 3.0 到 4.0 | hr |
Suggested Max Moisture | | | 0.020 | % |
Suggested Shot Size | | | 30 到 80 | % |
Hopper Temperature | | | 60 到 80 | °C |
Rear Temperature | | | 250 到 290 | °C |
Middle Temperature | | | 255 到 295 | °C |
Front Temperature | | | 260 到 300 | °C |
Nozzle Temperature | | | 275 到 300 | °C |
Processing (Melt) Temp | | | 275 到 300 | °C |
Mold Temperature | | | 60 到 90 | °C |
Back Pressure | | | 0.300 到 0.700 | Mpa |
Screw Speed | | | 40 到 70 | rpm |
Vent Depth | | | 0.038 到 0.076 | mm |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Instrumented Dart Impact | -30°C, Total Energy | ASTM D3763 | 54.0 | J |
Instrumented Dart Impact | 23°C, Total Energy | ASTM D3763 | 54.0 | J |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Flame Rating | 1.2 mm | UL 94 | HB | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.