Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
-- | | ASTMD792 | 1.58 | g/cm³ |
-- | | ISO1183 | 1.53 | g/cm³ |
Melt Mass-Flow Rate | 265°C/2.16kg | ASTMD1238 | 15 | g/10min |
Melt Volume flow Rate | 265°C/2.16kg | ISO1133 | 15.0 | cm3/10min |
Modeling Shrinkage | MD1 | 内部方法 | 0.40到0.80 | % |
Modeling Shrinkage | MD:3.20mm | 内部方法 | 0.40到0.80 | % |
Modeling Shrinkage | TD2 | 内部方法 | 0.60到1.0 | % |
Modeling Shrinkage | TD:3.20mm | 内部方法 | 0.60到1.0 | % |
Moisture Absorption | Saturation,23°C | ISO62 | 0.16 | % |
Moisture Absorption | Equilibrium,23°C,50%RH | ISO62 | 0.050 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Break | | ISO527-2/5 | 2.5 | % |
50.0mm Span | | ASTMD790 | 8450 | Mpa |
--9 | | ISO178 | 8500 | Mpa |
--10 | | ISO178 | 210 | Mpa |
Yield,50.0mm Span | | ASTMD790 | 165 | Mpa |
Taber Abrasion Resistance | 1000Cycles,1000g,CS-17Wheel | 内部方法 | 30.0 | mg |
--3 | | ASTMD638 | 9950 | Mpa |
Yield | | ASTMD638 | 115 | Mpa |
Yield | | ISO527-2/5 | 145 | Mpa |
Break | | ASTMD638 | 115 | Mpa |
Break | | ISO527-2/5 | 145 | Mpa |
Yield | | ASTMD638 | 2.0 | % |
Yield | | ISO527-2/5 | 2.4 | % |
Break | | ASTMD638 | 2.0 | % |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Flow:23 to 60°C | | ISO11359-2 | 2.2E-05 | cm/cm/°C |
Flow:-40 to 40°C | | ASTME831 | 7.5E-05 | cm/cm/°C |
Flow:23 to 60°C | | ISO11359-2 | 8.1E-05 | cm/cm/°C |
0.45MPa, Unannealed,3.20mm | | ASTMD648 | 208 | °C |
0.45MPa, Unannealed,100mm Span | | ISO75-2/Be | 217 | °C |
1.8MPa, Unannealed,3.20mm | | ASTMD648 | 190 | °C |
1.8MPa, Unannealed,100mm Span | | ISO75-2/Ae | 195 | °C |
-- | | ISO 8958-1998 | 202 | °C |
-- | | ASTMD1525,ISO306/A501222 | 220 | °C |
-- | | ISO306/B120 | 204 | °C |
Ball PressureTest | 125°C | IEC60695-10-2 | Pass | |
Flow:-40 to 40°C | | ASTME831 | 2.5E-05 | cm/cm/°C |
Electrical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Surface Resistivity | | IEC60093 | >1.0E+15 | ohms |
Volume Resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
Dielectric Strength | 0.800mm,in Oil | IEC60243-1 | 27 | KV/mm |
Dielectric Strength | 1.60mm,in Oil | IEC60243-1 | 23 | KV/mm |
Dielectric Strength | 3.20mm,in Oil | IEC60243-1 | 15 | KV/mm |
Relative Permittivity | 50Hz | IEC60250 | 3.30 | |
Relative Permittivity | 60Hz | IEC60250 | 3.30 | |
Relative Permittivity | 100Hz | IEC60250 | 3.60 | |
Relative Permittivity | 1MHz | IEC60250 | 3.20 | |
Dissipation Factor | 50Hz | IEC60250 | 8E-04 | |
Dissipation Factor | 60Hz | IEC60250 | 8E-04 | |
Dissipation Factor | 1MHz | IEC60250 | 0.013 | |
Comparative Tracking Index | CTI | UL746 | PLC2 | |
Comparative Tracking Index | | IEC60112 | 300 | V |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
-30°C | | ASTMD256 | 48 | J/m |
23°C | | ASTMD256 | 57 | J/m |
-30°C14 | | ISO180/1A | 8.0 | kJ/m² |
0°C15 | | ISO180/1A | 8.0 | kJ/m² |
23°C16 | | ISO180/1A | 9.0 | kJ/m² |
-30°C | | ASTMD4812 | 470 | J/m |
23°C | | ASTMD4812 | 480 | J/m |
-30°C17 | | ISO180/1U | 40 | kJ/m² |
23°C18 | | ISO180/1U | 45 | kJ/m² |
Charpy Notched Impact Strength | -30°C | ISO179/1eA | 9.0 | kJ/m² |
Charpy Notched Impact Strength | 23°C | ISO179/1eA | 9.0 | kJ/m² |
Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | 40 | kJ/m² |
Instrumented Dart Impact | 23°C,TotalEnergy | ASTMD3763 | 8.00 | J |
Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | 45 | kJ/m² |
Hardness | Test Condition | Test Method | Test Result | Unit |
---|
Rockwell Hardness | R-Sale | ISO2039-2 | 119 | |
Ball Indentation Hardness | H358/30 | ISO2039-1 | 110 | Mpa |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Flame Rating | 1.60mm,TestingbySABIC | UL94 | HB | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.